Products
-
Impact Bed
Reduce friction for the conveyor belts at the material feeding and transfer points, good sealing effect when used in conjunction with sealing skirt board.
-
Conveyor Belts Joint Vulcanizing Presses
Used for the heating vulcanization of joint connection and reparation of fabric ply conveyor belt, steel cord conveyor belt, PVC PVG solid woven fire- resistant conveyor belts.
-
-
Rubber Screw Belt Fastener
Conveyor belt fasteners for efficient repair in all conditions.
-
OTR
Off The Road Tyre
-
TBR
Truck Bus Tyre
-
PCR
Passenger Car Tyre
-
INNER TUBE
Inner tube is a ring-shaped elastic tube with a tire valve used to maintain the internal pressure of the tire. The valve is used to inflate and maintain a certain pressure in the inner tube. The inner tube shall have good air tightness, heat resistance, elasticity, aging resistance and small permanent deformation.
Inner tube is an air bearing container for inflation and damping. It is used as an auxiliary air bearing container in the inner cavity of truck, motorcycle, bicycle and rickshaw tires. It can be divided into natural rubber inner tube and butyl rubber inner tube according to the main materials.
-
FLAP
Flap is installed between the inner tube and the rim, the middle part is thicker, and the two edges are thinner from inside to outside. There is a center line on the outer surface of the flap for the main line during installation. There is also a hole on the center line for the inner fetal air valve mouth to pass through. The backing tape does not require high physical and mechanical properties of the rubber, but it should have good aging resistance. Tubeless tires fixed to deep rims and ultra-low pressure tires fixed to rims with special structures do not need falp due to tight fitting.
-
High Pressure Steel Wire Braided Rubber Hose
CONSTRUCTION：This hose is composed of an inner tube of oil synthetic rubber，a single wire braided reinforcement, and an oil and weather resistant synthetic rubber cover.
APPLICATIONS：It is suitable to carry hydraulic fluids, such as hydraulic oil, fuel oil, lubricants, emulsion, glycol and water, etc.
WORKING TEMPERATURE：from-40℃ up to+100℃
-
Single Wire Braid, Textile Covered Hydraulic Hose
CONSTRUCTION：This hose is composed of an inner tube of oil resistant synthetic rubber, a single wire braid reinforcement and a fiber braided cover.
APPLICATIONS：This hose is suitable for petroleum based hydraulic fluids within a
temperature range of -40℃～ +100℃ . -
Multispiral Hydraulic Hose
CONSTRUCTION：This hose is composed of an inner tube of oil resistant synthetic rubber, four spiral plies of steel wire wrapped in alternating directions, and an oil and weather resistant synthetic rubber cover.
APPLICATIONS： This hose is suitable for petroleum based hydraulic fluids within a temperature range of -40℃～ +120℃ -
Thermoplastic Hydraulic Hose
CONSTRUCTION：This hose is composed of an oil and water resistant synthetic rubber lining, one suitable textile yarn and an oil and weather resistant
APPLICATIONS：This hose is suitable for petroleum based hydraulic fluids within a temperature range of -40℃～ +93℃ . -
High Pressure Thermoplastic Hydraulic Hose
CONSTRUCTION：This hose is composed of an oil and water resistant synthetic rubber lining, two suitable textile yarns and an oil and weather resistant synthetic rubber cover.
APPLICATIONS： This hose is suitable for petroleum based hydraulic fluids within a temperature range of -40℃～ +93℃ . -
Water Suction and Delivery Hose
APPLICATION: Corrugated hose is used for water suction and discharge service, where a rugged yet exible hose is required by industry, building and agriculture, for overhead irrigation systems or for tank truck use.
TEMPERATURE RANGE: -30℃ to + 70℃
CONSTRUCTION: Tube: black, smooth, SBR rubber compound resistant to mud, sewage and waste water.
Reinforcement: high strengty synthetic cord plus helix wire.
Cover: black (wrapped nish) corrugated EPDM rubber compound weathering, ozone and ageing resistant. -
Dock Oil Hose
APPLICATION: Hardwall hose is used for suction and discharge of petroleum products from tankers and barges, bunkering service and industrial applications; suitable for aromatic content up to 50%.
Available with swaged -on (Transoil) ① or built-in (Transoil/RV) nipples with anges ②
APPLICABLE STANDARDS: BS 1435: 87 type S 15，UNI EN 1765: 99 type S 15 TEMPERATURE RANGE: -20℃ (-4°F) to + 82℃ (+185°F)
CONSTRUCTION: Tube: black, smooth, synthetic rubber compound; suitable for aromatic content up to 50%.
Reinforcement: high strength synthetic cord plus embedded steel helix wire and anti-static copper wires.
Cover: black, smooth (wrapped nish), synthetic rubber compound for a superior resistance to weathering, abrasion, oil and sea water. -
Textile Reinforced Hydraulic Rubber Hose
APPLICATIONS：
This hose is suitable for petroleum based hydraulic fluids within a temperature range of -40℃～ +93℃ .
APPLICATIONS：
synthetic rubber cover.
Hydraulic fluids in accordance with ISO6743-4 with the exception of HRD R、HFD S and HFD T at temperatures range of -40℃～ +100℃ . -
Double Fiber Braid (non-metallic), Rubber Covered Hydraulic Hose
CONSTRUCTION：This hose is composed of an inner tube of oil resistant synthetic rubber, a single wire braid reinforcement and a fiber braided cover.
APPLICATIONS： This hose is suitable for petroleum based hydraulic fluids within a temperature range of -40℃～ +100℃ .
-
Uncured Intermediate Rubber Strip, Noodles
Used as gap filling between the steel cords for the heating vulcanization of steel cord conveyor belt.
-
Steel Wire Spiraled Drilling Rubber Hose
CONSTRUCTION：It is composed of an inner rubber protection layer, middle rubber layer, steel wire spiraled layer and external rubber cover.
APPLICATIONS：Steel wire spiraled drilling rubber hoses are used in oil fields, well
cementing, well repairing, geological explorations, small drilling machine, and water conveyance at coal excavations, used to carry slurry, water at environmental temperature, and other uids.